Anti-Static Workwear Jackets Manufacturer: Fused Collar
Anti-static workwear jackets in 100% polyester twill with a fused collar, twin needle seams, reflective trim and zip pockets. Long sleeve, unisex, S to 6XL, six colours. Machine washable.
craftsmanship. Contact us for quotation!
A twill woven to keep static down
Anti-static workwear jackets start with the cloth. This one is a woven twill, 100% polyester, with anti-static fibres worked into the weave rather than sprayed on as a coating that washes away. That is the part that matters on a factory floor, in a workshop, or anywhere dry air and fast movement make a jacket crackle and cling. The twill is fine and substantial at once: it feels dense in the hand, it shrugs off scuffing against pallets and trolleys, and the colour holds through repeated washing. It breathes well enough for a warm shift, too. Read the anti-static side as a practical one: the cloth is built to resist a static build-up in everyday wear.

A collar that stays flat, and a covered zip
The collar is a plain point collar, and it is fused: the interlining is bonded into it, so the collar holds a flat, crisp edge instead of curling over after a few months of wear. The front closes with a full-length zip from the collar to the hem. Every zip on these anti-static workwear jackets is reverse mounted, with the flat side facing out and the teeth turned inward, so the front reads as one clean panel rather than a strip of metal down the middle. A storm placket runs over the zip to stop wind dropping through the teeth.

Bellows pockets, zip pockets and reflective trim
Two bellows pockets sit on the chest, each closed with a fused flap, and their folded sides give real depth for a phone, a notebook or a set of tools. Lower down there is a zip pocket at each side of the front, and reflective trim is set into the seams around the pockets, so it stays put instead of lifting at the corners after a hundred washes. The pen slot on the upper left sleeve carries the same reflective trim. Anti-static workwear jackets put the reflective detail where a light will catch it, rather than running it across the whole back.


Twin needle seams and a split back yoke
Look at the stitching and you can see where the time went. The main seams on anti-static workwear jackets are sewn with a twin needle, which lays two straight, even rows of stitching where a cheaper jacket would have one. That is what stops a hard-wearing jacket pulling apart at the shoulders and armholes after a season of use. Across the back the yoke is split and re-joined, a detail that lets the shoulders sit square without a tight pull across the blades. The cut stays clean and unfussy, the kind of jacket that looks the same on the hundredth wear as it did on the first.


Sizes, colours and logos
Anti-static workwear jackets come in a unisex block from S to 6XL and are held in six stock colours: light grey, dark grey, haze blue, bamboo green, dark navy and navy. Logos can go on by print or by embroidery. There is no lining to work around on this jacket, so a chest badge or a name can be embroidered, and larger artwork for the back goes on by heat transfer print or screen print. If the stock colours and sizes do not cover your team, anti-static workwear jackets can be made in your own colourway and size run. Please check the size chart before ordering.



Specification sheet
| Attribute | Specification |
|---|---|
| Type | Long sleeve workwear jacket |
| Fabric | Woven twill |
| Composition | 100% polyester with woven-in anti-static fibres |
| Fabric properties | Fine and substantial hand, hard wearing, good colour fastness |
| Anti-static | Woven-in anti-static fibres (not a certified ESD or PPE garment) |
| Collar | Point collar, fused for a flat, crisp edge |
| Front | Full-length zip from collar to hem, reverse mounted, covered by a storm placket |
| Chest pockets | Two bellows pockets with fused flaps |
| Hip pockets | One zip pocket at each side of the front, with reflective trim set into the seams |
| Sleeve pocket | Pen slot on the upper left sleeve with the same reflective trim |
| Zips | All reverse mounted, flat side out, teeth facing in |
| Back | Split yoke |
| Seams | Twin needle stitching at the main seams |
| Fit | Unisex |
| Size range | S to 6XL |
| Stock colours | 6: Light Grey, Dark Grey, Haze Blue, Bamboo Green, Dark Navy, Navy |
| Decoration | Print or embroidery |
| Care | Machine wash cold, mild detergent, do not bleach, hang dry, low iron, wash dark colours separately |

FAQ
Q: What is this jacket made of?
A woven twill, 100% polyester, with anti-static fibres worked into the weave. The twill is fine and dense, so it wears well, keeps its colour and absorbs less dust than a loose weave.
Q: Does the anti-static fabric actually work?
The cloth is woven with anti-static fibres, which help it resist a static build-up in everyday wear. It is not a certified ESD or PPE garment, and we do not hold test reports for a protection level, so if you need a certified anti-static garment for a hazardous area please contact us and we will tell you exactly what we can supply.
Q: Does it shrink in the wash?
It holds its size through normal washing. Machine wash cold with a mild detergent, do not bleach, and hang dry rather than tumble dry. Wash dark colours separately the first few times.
Q: Are the zips visible?
No. Every zip is reverse mounted, with the flat side facing out, so the teeth sit turned inward and the front of the jacket reads as a clean panel instead of a row of metal teeth.
Q: Can you print or embroider a logo?
Yes, either. A small chest badge or a name works well in embroidery, and larger artwork for the back goes on by heat transfer print or screen print. Send us your artwork and we will confirm the best method for the placement.
Q: How should I wash it?
Machine wash cold with a mild detergent, do not bleach, hang dry, and use a low iron if needed. Wash dark colours separately.
Recommended Products · Popular Picks
4 items · Based on your browsing






