Custom Workwear Jackets: Reflective Trim, Short Sleeve
Custom workwear jackets in a T/C poly-cotton blend with reflective trim, two-tone panels, a zip front and chest pockets. Short sleeve, unisex, S to 4XL, three colours. Machine washable.
craftsmanship. Contact us for quotation!
A T/C blend built for warm shifts
Custom workwear jackets begin with cloth, and this one is a woven T/C blend: 63% polyester and 32% cotton, with a small amount of spandex for give and a touch of viscose for softness. That mix is deliberate. Polyester holds the colour and takes the abrasion, cotton keeps air moving next to the skin, and the hand feel stays soft rather than slick. Colour fastness is good, so the navy that goes out on Monday is still navy after a season of wash cycles. The cloth resists scuffing against pallets, trolleys and door frames, and it absorbs moisture and breathes well enough to wear through a warm shift without turning clammy. That is where a workwear jacket earns its keep, in the heat rather than in the cold.

Zip front, chest pockets and a pen slot
Across the front, custom workwear jackets close with a full-length zip from the collar to the hem, and a storm flap covers it so the front stays flat and wind does not drop down the teeth. Two large patch pockets sit on the chest, each closed with a flap, and a strip of reflective trim is set into the seam above each flap, so it will not lift at the corners after a hundred washes. Lower down there is a slanted pocket at each side of the front. On the left sleeve a small pen slot is edged with a 1 cm contrast strip, the kind of detail a plain work shirt does not carry.

Two-tone panels and the split back yoke
Every jacket is made in two colours. One shade covers the body, and a second shade is carried into the inner face of the short sleeve, the upper side panels, the inside of the front placket and the inner face of the storm flap. Custom workwear jackets use the second colour as a trim line rather than decoration, so the eye reads the cut of the garment from across a yard. Across the back the yoke is split and re-joined, with a strip of reflective trim running through the seam, and the yoke is double layered with a knitted mesh on the inside, so the shoulders breathe where a backpack or a harness would sit. At each side of the hem a small tab fastens with a snap, so the hem can be pulled in or left loose.

Where it fits and the matching trouser
These are late spring, summer and early autumn jackets: warm weather workwear rather than winter kit. The sleeve is short, the cloth is light and the weave lets air move, which suits factory floors, warehouses, logistics yards and site crews. Custom workwear jackets are cut unisex, so a single order covers a mixed team without splitting the sizing. A matching work trouser is available, cut in the same cloth with belt loops, a zip fly and a pocket at each side, so the set reads as one uniform. The jacket is supplied on its own or as a jacket and trouser set. Left open over a t-shirt it also works as a light cover layer on a warm afternoon.

Sizes, colours and logos
Custom workwear jackets come in a unisex block from S to 4XL and are held in three stock colours, all made as a two-tone: navy, light grey and crab green. Logos can go on by print or by embroidery. On a short sleeve jacket of this weight both routes work cleanly, because there is no lining to work around: a chest badge or a name can be embroidered, and larger artwork for a back print goes on by heat transfer or screen print. If the stock colours and sizes do not cover your team, custom workwear jackets can be made in your own colourway and size run. Please check the size chart before ordering.

Specification sheet
| Attribute | Specification |
|---|---|
| Type | Short sleeve workwear jacket |
| Fabric | Woven T/C poly-cotton |
| Composition | 63% polyester, 32% cotton, 3.3% spandex, 1.5% viscose, 0.2% nylon |
| Fabric properties | Good colour fastness, hard wearing, moisture absorbent and breathable |
| Collar | Stand collar |
| Front | Full-length zip from collar to hem, covered by a full storm flap |
| Chest pockets | Two patch pockets with flaps, reflective trim set into the seam above each flap |
| Hip pockets | One slanted pocket at each side of the front |
| Sleeve pocket | Pen slot on the side of the left sleeve, 1 cm contrast strip along the top edge |
| Colour structure | Two-tone: one main colour and one second colour |
| Contrast placement | Inner face of the short sleeve, upper side panels, inside of the front placket and the inner face of the storm flap |
| Back | Split yoke re-joined with reflective trim in the seam, double layered with a knitted mesh inside |
| Hem | Adjustable tab with a snap at each side |
| Fit | Unisex |
| Size range | S to 4XL |
| Stock colours | 3: Navy, Light Grey, Crab Green |
| Matching trouser | Available, with belt loops, a zip fly and a side pocket at each side |
| Decoration | Print or embroidery |
| Care | Machine wash cold, mild detergent, do not bleach, hang dry, low iron, wash dark colours separately |

FAQ
Q: What is this jacket made of?
A woven T/C poly-cotton: 63% polyester, 32% cotton, 3.3% spandex, 1.5% viscose and 0.2% nylon. The polyester carries the colour and the wear, the cotton keeps it breathing, and a small amount of spandex gives the cloth a little give.
Q: Does it shrink in the wash?
It holds its size through normal washing. Machine wash cold with a mild detergent, do not bleach, and hang dry rather than tumble dry. Wash dark colours separately the first few times.
Q: Is it a jacket or an overshirt?
Both readings work. It is a short sleeve stand collar jacket with a full-length zip and a chest pocket, and the weight sits between a light jacket and a work shirt, which is what makes it useful through late spring, summer and early autumn.
Q: Is the reflective trim just on the chest?
No. There is a strip set into the seam above each chest pocket flap, so two across the chest, and a third runs through the split seam of the back yoke. All three are set into the seam rather than applied on top, so they stay put through repeated washing.
Q: Is the trouser included?
The price shown is for the jacket on its own. A matching work trouser is available in the same cloth, with belt loops, a zip fly and a side pocket at each side. Contact us and we will send photographs and a price for the jacket and trouser set.
Q: Can you print or embroider a logo on it?
Yes, either. There is no lining to work around on this jacket, so a chest badge or a name can be embroidered, and larger artwork for the back goes on by heat transfer print or screen print.
Recommended Products · Popular Picks
4 items · Based on your browsing






